PEFLEX Accessories
Air diffuser is an element of the ventilation system used to regulate and distribute air flow in the rooms. It can supply or extract air and is part of the air distribution system in mechanical ventilation systems.
Designer air diffusers from the DVSR and DVSER series feature a modern look that complements contemporary home interiors, and the square bends give them an original form.
They are made of powder-coated steel sheet in white (RAL 9016) with a glossy finish. The rotating disk allows you to smoothly adjust the amount of air flow.
Available diameters
100 mm
125 mm
160 mm
A slot diffuser is a type of an air diffuser which is a component of a ventilation system designed to introduce air into a room through narrow slots. This is a special type of diffuser that is placed on the wall or ceiling and allows airflow to be distributed evenly along the room.
Dedicated boxes
The PEFLEX damper is an innovative solution that allows for smooth regulation of airflow and dampening of noise in ventilation installations.
It can be successfully used on both supply and exhaust ducts. Mounting in front of the air diffuser allows the system to achieve optimum performance.
PEFLEX damper is a particularly useful solution in cases where it is necessary to adjust the airflow at a specific point, and the adjustment with anemostat generates undesirable noise.
- It is made of special acoustic foam designed to dampen the noise of flowing ventilation air.
- The rotating design allows for smooth regulation, while additional retractable elements enhance the damper's throughput.
Available diameters
100 mm
125 mm
160 mm
The intake and exhaust grille is a component of the ventilation system used to bring air in or out of the recuperator and ventilation system.
The PEFLEX grille has been embedded into a square field and features a modern design. The angled laths protect the installation from rain and wind, and their special design does not generate additional air resistance. There is also a large drip cap at the bottom to prevent the formation of streaks on the wall.
The PEFLEX air intake/exhaust grille is made of durable, thick and weather-resistant grind stainless steel. It has been adapted for installation vertically on the facade and horizontally in the roof soffit.
Inlet diameter
196 mm
245 mm
310 mm
The CLICK connector is used to connect two sections of PEFLEX duct. It helps to utilize remaining ends of the ventilation ducts or to extend a single duct. It is built with CLICK system couplers that have built-in gaskets and snaps to hold the duct.
The dedicated PEFLEX connector allows to quickly and securely join two sections of a duct tightly – without the need for additional gaskets, clips and without using tape.
- The only connector available on the market for connecting PE ventilation ducts with a built-in gasket and CLICK mounting!
- Three dimensional variants for connecting PEFLEX ventilation ducts with diameters of 50, 75 and 90 mm.
Available diameters
50 mm
75 mm
90 mm
PEFLEX offers two types of plugs:
- plugs with diameters ranging from 50 to 90 mm allowing to seal the duct or unused CLICK connectors in plenum and distribution boxes
- plugs with diameters ranging from 100 to 250 mm allow to temporarily seal the diffuser spigots or plenum boxes extensions, manifolds spigots and EPS ducts during the finishing of installation
Available diameters
50 mm
75 mm
90 mm
100 mm
125 mm
160 mm
200 mm
250 mm
The PEFLEX cutter was the first dedicated PE duct cutter on the market.
Its special design allows for an even cut of the ventilation duct with a single movement creating the edge that is straight and free of burrs.
Using the PEFLEX cutter, you can easily and quickly cut or trim the duct to the required length, significantly speeding up the process of installing the recuperation system in the house.
Available diameters
50 mm
75 mm
90 mm
PEFLEX adapters allow to change the diameters of ventilation ducts. They are particularly useful when ducts cross each other or there is a collision with other installations in the building.
The adapters allow the transition from 75 mm diameter to 50 mm diameter while maintaining similar air resistance and enabling transmitting the same amount of air.
This is very important because a smaller diameter duct is able to transport less air, thus it is necessary to increase their quantity to compensate for the reduced cross-sectional area of the ducts.
Available diameters
2×75 / 5×50 mm
Specially designed for the installation of ventilation ducts, the PEFLEX ducting clamp is an innovative solution that allows for easy installation of recuperation systems on the ceiling and wall, even by one person.
The special design allows the clamps to be connected together, so you can aesthetically mount several ducts side by side using fewer studs to the ceiling, significantly speeding up the installation process.
The special design allows the clamps to be connected together, so you can aesthetically mount several ducts side by side using fewer studs to the ceiling, significantly speeding up the installation process.
- Speeding up the ventilation system installation and simplifying the process of mounting ducts to the ceiling and walls, which can now be done by a single person!
Available diameters
75 mm
PEFLEX sleeve is designed to insulate PEFLEX ventilation ducts with diameters of 50, 75 and 90 mm and is made of two layers of heavy-duty PE film between which there is insulation with a thickness of 25, 50 and 75 mm.
PEFLEX sleeves use dust-free polyester fiber insulation instead of standard mineral wool, which does not bite or dust during installation.
Additional insulation of ventilation ducts is used when they run through colder rooms.
- Quick and easy protection of the recuperation system against heat loss.
Insulation thickness
25 mm
50 mm
75 mm
FSA conical filters for round anemostats are used to protect mechanical ventilation ducts from contamination.
Thanks to the special filter fabric shaped into a cone, impurities such as dust, insects and grease are captured on its surface, thus protecting the entire section of the installation – from the air diffuser to the recuperator.
- Adapted for installation in standard round air diffusers and available in several sizes.
- Recommended for installation in exhaust points in areas such as kitchens, bathrooms, utility rooms, etc.
Available diameters
100 mm
125 mm
160 mm
